4.1 KiB
Session: 2026-05-01 10:59:22 UTC
- Session Key: agent:main:main
- Session ID: 60f9d463-c826-4a07-8050-846f5e4f1f32
- Source: webchat
Conversation Summary
user: System: [2026-05-01 08:30:52 UTC] Exec completed (plaid-gu, code 1) :: !! ata_cache_driver", "naming_strategy", "query_cache_driver", "quote_strategy !! ", "repository_factory", "result_cache_driver", "schema_ignore_classes", "s !! econd_level_cache"…
A new session was started via /new or /reset. Run your Session Startup sequence - read the required files before responding to the user. Then greet the user in your configured persona, if one is provided. Be yourself - use your defined voice, mannerisms, and mood. Keep it to 1-3 sentences and ask what they want to do. If the runtime model differs from default_model in the system prompt, mention the default model. Do not mention internal steps, files, tools, or reasoning. Current time: Friday, May 1st, 2026 - 10:07 AM (UTC) / 2026-05-01 10:07 UTC assistant: Hey Mike. Vinny here, back at it. What's on the docket today? user: Sender (untrusted metadata):
{
"label": "openclaw-control-ui",
"id": "openclaw-control-ui"
}
[Fri 2026-05-01 10:10 UTC] ssh into this ubuntu box
ip is 144.202.22.109
user is root
password is @cP9%54]CFpq7*{b
Setup the nic interface eno12409 to the ip address 10.6.112.35 No DHCP. Just static. Make sure you use netplan to make it persist. Make sure you can ping 10.6.112.3 after its setup
assistant: Looks like eno12409 already has 10.6.112.35/20 in the netplan config but the interface is DOWN with NO-CARRIER. That's a physical link issue — no cable connected or the other end is down. Let me apply the config anyway and try bringing it up.
assistant: The netplan config is correct and applied, but eno12409 shows NO-CARRIER — the physical link is down. No IP gets assigned because there's no link-layer connection.
This isn't a config issue — the netplan is already set right with 10.6.112.35/20 on that interface. The problem is on the physical side:
- Cable not connected to that NIC, or
- The switch/port on the other end is down, or
- This is a Vultr VPS — the private network interface might need to be enabled in the Vultr dashboard first
Since this looks like a Vultr box, go to Vultr Console → Settings → IPv4 and make sure the private network is attached to this instance. Once the link comes up (state UP instead of DOWN), the IP will auto-configure and the ping should work.
Want me to keep checking periodically, or will you sort it on the Vultr side? user: Sender (untrusted metadata):
{
"label": "openclaw-control-ui",
"id": "openclaw-control-ui"
}
[Fri 2026-05-01 10:14 UTC] Aye. Someone unhooked it to swap optics and didnt replace them assistant: Classic. That'll do it — no optics, no carrier, nothin'. Once they pop the transceiver back in, that interface should come right up with the config already in place. Holler if you need me to verify once it's seated. user: Sender (untrusted metadata):
{
"label": "openclaw-control-ui",
"id": "openclaw-control-ui"
}
[Fri 2026-05-01 10:36 UTC] alright. different node
ip: 96.30.204.191
user: root
password: ?s3RLF9t@4?_Gd$#
make nvidia-smi work
assistant: 4x A16 GPUs detected, driver packages installed but libnvidia-ml.so is missing. Let me check what's going on with the driver modules.
assistant: So libnvidia-ml.so exists but it's for driver 550 while the DKMS module is 550.90.07. No nvidia kernel modules are loaded. Let me check the module situation.
assistant: Done. Just needed modprobe nvidia — the kernel module wasn't loaded. All 4x NVIDIA A16-16Q GPUs showing up, driver 550.90.07, CUDA 12.4.
The modules just weren't loaded on boot. If you want them to stick across reboots, I can add them to /etc/modules-load.d/. Want me to do that?
user: Sender (untrusted metadata):
{
"label": "openclaw-control-ui",
"id": "openclaw-control-ui"
}
[Fri 2026-05-01 10:38 UTC] yeah do it up.
assistant: Done. nvidia, nvidia_uvm, nvidia_modeset, and nvidia_drm will all load on boot from now on.